Types of Propeller Shaft, Its Removal and Refitting Procedure

The propeller shaft, sometimes also known as Cordon shaft or drive shaft is the medium by which the power from the engine driven gearbox is transmitted to the driving axles. It is made of steel and whether fitted in a front or rear wheel drive or between the main gearbox and an auxiliary gearbox, conforms to a similar pattern in which, one or two universal joints are incorporated. If required length of propeller shaft is more, then centre bearing is placed at centre of the shaft. It may be more than one to avoid’ whip.’

TYPES OF PROPELLER SHAFT

(a) Open Type Propeller shaft. The shaft is tubular in cross section and not enclosed in any outer casing or tube. It is fitted with a universal joint at each end, used on all heavy commercial vehicles and on most types of cars and light vehicles.

(b) Enclosed Type of Propeller Shaft. The propeller shaft is smaller in diameter than the open type and is supported by roller bearings inside the torque tube at the front and rear; in some models there is no central bearing. There is only one universal joint fitted and this is located at the front end adjacent to the gearbox.

OPEN TYPE PROPELLER SHAFT

(a) This type is generally used on all heavy commercial vehicles and on most types of cars and light vehicles. The shaft is tubular in cross section and not enclosed in any outer casing or tube. It is fitted with a universal joint at each end, one to the gearbox main shaft through flange and the other to the driving axle bevel pinion shaft. On vehicles where the propeller shaft is comparatively long the shaft is made up of two portions connected by an additional universal joint and supported to the chassis cross member by a bearing. This centre bearing or support functions as a steady to obviate ‘Whip’ which may develop in the shaft.

Open Type Propeller Shaft

(b) The front universal joint is splined to the propeller shaft and provides a telescope action for any fore and aft movement of the rear axle relative to the gearbox. When reassembling, the yokes of both universal joints must be in line and the correct position is usually indicated by arrows on the universal joints sleeve and on the propeller shaft.

ENCLOSED TYPE PROPELLER SHAFT

This type is of the solid cross section and is more often enclosed in a tubular structure known as the ‘Torque Tube’ which is rigidly connected at its rear end to the rear axle casing and front end connected to the gearbox casing by a ball joint. As this tube resists the torque and twisting motion of the rear axle casing (due to the application of brakes) and reaction of the drive, it is named torque tube. The propeller shaft is smaller in diameter than the open type and is supported by roller bearings inside the torque tube at the front and rear; in some models there is no central bearing. There is only one universal joint fitted and this is located at the front end adjacent to the gearbox. The rear end of the shaft is attached to the bevel pinion shaft by a splined sleeve, which is secured by rivets to both the shafts to prevent longitudinal movement.

REMOVAL OF PROPELLER SHAFT

Procedure of Removal

(a) Unscrew bolts fastening rear propeller shaft coupling with the rear axle tail pinion coupling with the rear axle tail pinion. Carefully lower rear end of the propeller shaft on the ground.

(b) Disconnect fastening bolts of the rear propeller shaft from the front coupling carefully remove the rear propeller shaft.

Note:- Do not remove the sliding yoke from the propeller shaft.

(c) Remove bolts holding centre bearing bracket of the front propeller shaft from the chassis cross member. Carefully lower the propeller shaft on the ground.

(d) Remove the coupling bolts of the front propeller shaft from the transmission end and remove front propeller shaft.

PROCEDURE OF REFITTING OF PROPELLER SHAFT

(a) Clean the mating surface of the coupling flanges on the tail pinion. Similarly, clean the mating surface on the centre bearing bracket and the chassis cross member.

(b) Connect the front coupling flange of the front propeller shaft to the transmission coupling flange.

(c) Suspend the centre bearing bracket on the chassis cross member through its bolts.

(d) Connect the front coupling flange of the rear propeller shaft to the centre bearing bracket rear flange on the chassis cross member through its bolts.

(e) Connect the rear coupling flange of the rear propeller shaft to the tail pinion coupling flange through its bolts.

(f) Grease all the nipples of the propeller shafts and universal joints and road test the vehicle.

Support Us By Sharing

Author: Aliva Tripathy

Taking out time from a housewife life and contributing to AxiBook is a passion for me. I love doing this and gets mind filled with huge satisfaction with thoughtful feedbacks from you all. Do love caring for others and love sharing knowledge more than this.

Leave a Reply

Your email address will not be published. Required fields are marked *

*

code